2010 Ford Escape 3.0 Oil Type, Capacity, Filter & Change Cost

2010 Ford Escape 3.0 Oil Type: The 2010 Ford Escape 3.0 is a well-known and popular SUV recognized for its reliability and performance. 

In order to keep the Escape running at its best it is essential to make sure you use the right type of oil and to change it on a regular basis.

Oil Type: Ford suggests using SAE 5W-20 synthetic oils in the Escape 3.0 for 2010. Escape 3.0. Synthetic oil is more secure and may help prolong the life of your engine.

Capacity: The capacity of oil for the Escape 3.0 in 2010 Escape 3.0 is 6 quarts. Make sure to keep track of the oil levels regularly and add oil if required.

Filter: The Escape 3.0 of 2010 Escape 3.0 uses a Motorcraft FL-500S oil filter. The filter needs to be replaced at least every when you replace the oil.

Cost of Change: The cost of changing an oil filter in a Ford Escape 3.0 will differ depending the location where it is completed. But, you should expect to spend between $100-$80 to have an oil replacement at a dealer. 

2010 Ford Escape 3.0 oil capacity

The Ford Escape 3.0 engine comes with a capacity for oil of six Quarts (5.7 liters) with a brand-fresh oil filter. 

It is essential to use the recommended type of oil and weight that is appropriate for your vehicle and is usually specified inside the manual for the driver. 

For this specific vehicle, Ford recommends using 5W-20 synthetic blend motor oil. It is a mixture of conventional and synthetic oils and provides superior performance and protection than conventional oils alone.

When it comes time to change the engine oil, it’s suggested to change it each 7,500 miles or every 12 months, whichever is first. 

However, if you often operate in harsh environments such as high temperatures or dusty areas It is best to change your oil more often to ensure the best performance of your engine.

Ford Escape 2010 3.0 oil type

The recommended oil for the Ford Escape 3.0 engine is 5W-20 synthetic blend motor oil. The synthetic blend is a mixture of conventional and synthetic oils that offer greater performance and protection over conventional oil by itself.

To be sure you’re using the proper oil type for your specific car, it is always advised to consult the owner’s manual or speak with a qualified repair.

Also, it’s essential to change your oil regularly and test the level of oil and condition often to ensure maximum engine performance and security.

Intervals between Oil Changes

Regularly changing oil is essential for maintaining the good condition of your car. For the Ford Escape 3.0 in 2010, it is suggested to change your oil each time you drive.

Ford Escape 3.0 and it is recommended to change the oil at 700 miles or as per the intervals specified in the owner’s instruction manual.

It is advised to keep track of the amount of oil frequently and monitor its condition to make sure it’s maintained and at a satisfactory level.

2010 Ford Escape 3.0 oil filter

The Ford Escape 3.0 engine has an oil filter that has the part number Motorcraft FL-910S. Always verify the owner’s manual or consult with a qualified mechanic to ensure you’re using the correct oil filter for your vehicle.

Furthermore, changing the oil filter simultaneously with the oil ensures peak engine performance and safety.

2010 Ford Escape oil change

To change the oil on the Ford Escape from 2010, you must follow these steps: Ford Escape, follow these steps:

1. Place your vehicle in an area that is level.
2. Switch off the engine and remove the hood.
3. Find the cap for the oil filler and take it off.
4. Install an oil drainage pan beneath the plug for draining oil.
5. Make use of a wrench for loosening the plug that drains oil.
6. Let the oil be drained from the pan.
7. After the oil has been drained replace the drain plug and tighten it up using the help of a wrench.
8. Introduce new oil to the engine via the neck of the oil filler.
9. Replace the cap on the oil filler.
10. Get the motor started and allow it to run for a couple of minutes.
11. Make sure the oil is at the right level, and add oil if required.
12. Close the hood, and you’re done!

People Also search for the 2010 Ford Escape 3.0 oil type

Conclusion

Thank you for taking time to read this article on the Ford Escape 2010 3.0 engine type! I hope that you found it useful.

It is essential to select the right type of oil for the 2010 Ford Escape 3.0 to ensure it runs well and to extend its lifespan. Ford suggests using the SAE5W-20 type of synthetic oil. This type of oil at a majority of automotive parts shops.

If you’re unsure of the best way to replace your oil on your own, go to a certified mechanic. But changing your oil on your own is an easy job that could save you money over the long term.

Follow the guidelines in this article to make sure the 2010 Ford Escape 3.0 receives the necessary oil maintenance. Enjoy your day!

For more posts visit our website: https://engineoiil-capacity.com/

FAQs –  2010 Ford Escape 3.0 oil type

What is the 2010 Ford Escape XLT oil capacity?

According to our sources, oil, coolant, and fuel capacity for this version of the 2010 Ford Escape XLT 4WD 3.0L V-6 automatic are as follows: Engine lubricant oil capacity: 5.7 liter / 6 U.S. qt / 5 imp.

What kind of oil does a Ford Escape take?

 The ideal motor oil to use for the Ford Escape is determined by the year of manufacture, make, and the type of engine. A 2.5L V6 engine with an automatic transmission needs 5w-30 synthetic oil, but a 3.0L with a manual transmission needs 10w-30 conventional oil.

What kind of coolant does a 2010 Ford Escape take?

Ford Escape Electric/Gas / Gas 2010, Gold Prediluted Engine Coolant, 1 Gallon by Motorcraft®. Volume: 1 Gallon. Color: Yellow. Quantity: 1 Jug. Motorcraft is the way to restore the performance of your vehicle. Designed specifically for… Ford Escape Electric/Gas / Gas 2010, Gold Concentrated Engine Coolant by Motorcraft®. Color: Yellow.