2017 Subaru Crosstrek Oil Type: Maintaining Your 2017 Subaru Crosstrek running smoothly is the result of regular maintenance which includes oil replacements. a vital element.
With different Types of oil capacity, filters, And prices, picking the right one can be difficult. Worry not, adventurous driver!
This guide, compiled using the official Subaru sources And current information, will arm you with the necessary information to ensure that your Crosstrek’s engines are running smoothly And your bank account is sated.
2017 Subaru Crosstrek Oil Type
The 2017 Crosstrek makes use of 5W-30 synthetic oil, particularly Subaru Genuine SN/GF-5 5W-30 synthetic oil.
This premium oil offers optimal protection and lubrication to your engine across a wide variety of driving conditions including city commutes and mountain excursions.
2017 Subaru Crosstrek Oil Capacity
The cross trek’s capacity for oil is contingent on the size of the engine:
- 2.0L engine: 4.7 quarts (4.4 liters)
- 2.5L engine: 5.1 quarts (4.8 liters)
2017 Subaru Crosstrek Oil Filter
Subaru suggests using an authentic Subaru oil filter to ensure the best performance and filtering. The exact part number of the filter is dependent on the size of your engine:
- 2.0L engine: 154002A
- 2.5L engine: 154003A
2017 Subaru Crosstrek Oil Change Cost
The cost of a change in the oil on your Crosstrek will differ based on whether you go with an independent or a dealer mechanic, the kind of oil you choose to use, and the place you live. This is a basic breakdown:
- Dealership: $82 – $119
- Independent mechanic: $78 – $95
2017 Subaru Crosstrek Engine Specs
The Subaru Crosstrek is available in 2017. Subaru Crosstrek comes with a single engine choice which is it’s a 2.0-liter 4-cylinder horizontally opposed (H4) gasoline motor. These are the most important details:
| Specification | Value |
|---|---|
| Engine Type | 2.0L H4 DOHC 16-valve |
| Displacement | 2.0 Liters (122 cubic inches) |
| Horsepower | 148 hp @ 6200 rpm |
| Torque | 145 lb-ft @ 4200 rpm |
| Fuel System | Sequential MPI |
| Transmission (Standard) | 5-speed manual |
| Transmission (Optional) | Continuously variable transmission, with manual mode |
| Drivetrain | All-wheel drive |
| Fuel Economy (EPA) | |
| * City | 29 mpg |
| * Highway | 33 mpg |
| * Combined | 30 mpg |
| Additional Features | Direct injection, Active valve control, Variable valve timing |
2017 Subaru Crosstrek Oil Change
- Place your Crosstrek on an even surface. Then, use the brake for parking.
- Lift the hood to locate the cap that fills with oil. The cap should be removed and put it aside.
- Find the oil drain plug under the engine. Put the drain pan underneath the plug, then loosen it using the wrench. Be cautious, as the oil is hot!
- Allow the oil to drain completely. It could take a few minutes.
- Once the oil is gone down, take out the old filter. You may require an oil wrench to complete this task. Be cautious not to spill any oil.
- Apply a light coat of oil on the gasket of the new filter. Install the new filter by hand until it is snug Then tighten it a further 1/4 turn using the wrench.
- Replace the drain plug for oil and tighten it up to the torque you need (15 Ft-lbs for the majority of Crosstreks).
- Inject the new oil into the engine and check the dipstick often to avoid filling too much. The Crosstrek uses five quarts of oil, including an oil filter change.
- Replace the cap that fills up with oil and then start the engine. It should run for a couple of minutes and then look for leaks.
- Switch off the engine and then check the level of oil. If needed, add more oil.