EA190V Oil Type, Capacity, Filter & Change Cost


EA190V Oil Type:  Learn the EA190V oil type And capacity, As well As the costs of filter changes, in this comprehensive guide. Get to know the EA190V and its engines.

Find out how you can keep them running smoothly. Exploring the benefits And importance of using high-quality oil filters as well as regular oil changes will help to prolong the engine’s life.


Don’t miss expert advice for EA190V engines – read it now to ensure that your vehicle performs at its best.

EA190V Oil Type

The recommended engine oil for the EA190V is SAE 10W-30 or 20W-40 depending on ambient temperature.


The following is a list of recommended oils for various temperature ranges.

Engine modelOil typeLubrication systemOil Capacity (L)Notes
EA190VSAE 10W-30 20W 30WMechanical splashing0.6Use API SG or greater oil. When choosing a specific viscosity, consider the climate and operating conditions.

Top Brands of Subaru EA190V Engine Oil

For the best performance to the best performance of your Subaru EA190V engine, go for oil brands that are reputable and known for their quality and dependability. 

The top brand names are Mobil 1, Castrol, Pennzoil, and Valvoline. Always refer to the manufacturer’s guidelines for brands that are approved.

Subaru EA190V Oil Capacity

It is estimated that the Subaru EA190V engine’s capacity for oil is around 0.58 Liters (or 0.61 Quarters) when it comes to changing the filter and oil. 

However, it is advised to consult the owner’s manual for your specific model to ensure that you Are getting the most up-to-date And current information on the model and year of your choice. 

Monitoring And keeping the correct oil level is essential for keeping the engine running smoothly And guaranteeing its long-term durability.

EA190V Engine Specifications

Engine modelEA190V
Engine type4-stroke, OHV, single-cylinder
Displacement189 cm3, (11.53 cu·in)
Max. horsepower5.6 PS (4.1 kW; 5.5 HP) at 3,600 rpm
Max. torque11.2 N·m (1.1 kg·m, 8.3 ft·lb) at 2,500 rpm
Cooling systemForced air
Air cleanerFoam (Optional Paper)
Lubricating systemSplash type
Ignition systemCapacitance discharge type
Fuel systemFloat type carburetor
Fuel consumption395 g/kWh
Fuel tank capacity1.0 L (0.26 US. gal. 0.22 Imp. gal.)
Fuel usedUnleaded gasoline (octane number 86 or higher)
Starting systemRecoil starter
Stopping systemIgnition primary circuit ground
GovernorCentrifugal flyweight type
PTO shaft rotationCounterclockwise view from P.T.O. side
Dimensions (L x W X H)425 x 360 x 290 mm (16.7 x 14.2 x 11.4 in)
Dry weight14.0 kg (30.9 lbs)

Subaru ea190v Oil Filter

There are several different oil filters for the Subaru EA190V, depending on your Subaru model and the year your engine was manufactured. Subaru 152084A – 000 is the most commonly used oil filter on the EA190V engines.


It is a spin-on filter. Subaru 152084A-110, Subaru 152084A-390, and Subaru 152084A-490 are other oil filters that may be used with the EA190V.

You can consult the owner’s guide or contact your Subaru dealer if you are not sure which oil filter you need for your Subaru EA190V.

DescriptionYou can also value
ItemSubaru ea190v oil filter
CategoryAutomotive Parts
SubcategoryEngine Oil Filters
KeywordsOil filter for Subaru EA190V engine maintenance

Subaru EA190V Oil Change

  1. Warming up the engine. Run the motor for A few moments to warm up the oil. This will make it easier to drain.
  2. Always park on an even surface. You will be able to drain all the oil properly.
  3. Place a drain pan below the engine. Locate an oil drain plug on the crankcase near the bottom and place the pan underneath.
  4. Loosening the oil drainage plug: With the wrench, loosen the drain plug carefully And allow the oil to drain fully into the pan. Oil may be very hot.
  5. Replace oil filter: After the oil has been drained from the engine, remove the old filter using the wrench. Take care not to spill oil into the engine compartment. Wipe down the sealing surface with a clean cloth. Install the new filter with your hands until snug. Use the wrench to tighten it for another 1/2- 3/4 turns. Avoid over-tightening.
  6. Reinstalling the oil drain Plug: Replacing the oil filter plug, And tightening it securely with the wrench. Don’t over-tighten.
  7. Add oil: Use your funnel to Add the recommended amount into the engine’s fill port. (Refer to your owner’s manual for exact measurements).
  8. Check your oil level. Remove And clean the dipstick. Then, pull it out once more and check the level of oil. You should see the oil between the two marks. You can add more oil as needed.
  9. Start up the engine to check for leaks. Let the engine run for several minutes. Search for any leaks in the area of the oil drain plug or the oil filter. Check the oil level after the engine is turned off.
  10. Dispose of the used filter And oil properly: Bring the used filter And oil to your local recycling center. Don’t throw them away or flush them down the sink.


Selecting the appropriate oil type is essential to ensure the maximum performance and longevity of the Subaru engine. 

Following the manufacturer’s suggestions by using the proper viscosity and adhering to regular maintenance, you will benefit from a strong and effective engine for many years to be.

For more posts visit our website: https://engineoiil-capacity.com/

FAQs – EA190v oil type

What is the oil capacity of the ea190v?

Oil Capacity EA190V ……. 20 oz (600cc) 2. Re-install the drain plug before refi lling oil. 3. Oil may need to be changed more often if operating in dusty or hot environments. Page 18 • Foam Element Remove the element and wash it in a solution of mild detergent and warm water. Then rinse the element thoroughly in clean water.

What is the Subaru ea190v pressure washer?

Specifically, this model makes use of what’s known as an ea190v engine. It’s known for having a high oil capacity, a big oil, and fuel tank capacity, and a vertical chain-driven OHC. What Are The Subaru ea190V Pressure Washer Parts?

What kind of engine does a Subaru Robin ea190v have?

The Subaru-Robin EA190V is a 189 cc (11.53 cu-in) single-cylinder air-cooled 4-stroke internal combustion general-purpose gasoline engine with vertical shaft manufactured by the Industrial Products division of Subaru Corporation under the Subaru Industrial Power Products brand name (other names: Robin, Subaru-Robin and Wisconsin Robin).

What kind of oil do you use in a 4-stroke?

Page 12 • Use 4-stroke automotive detergent oil of API service class SE or higher grade. • Select the viscosity based on the air temperature at the time of operation as shown in the table. Oil Capacity EA190V ……. 20 oz (600cc) Upper Mark Oil Dipstick Lower Mark…